Pilotes d'imprimante SATO
Imprimantes prises en charge
- Bidirectional Rfid SATO CG208
- Bidirectional Rfid SATO CG212
- Bidirectional SATO CG408
- Bidirectional SATO CG412
- Bidirectional Rfid SATO CL408e
- Bidirectional Rfid SATO CL412e
- Bidirectional Rfid SATO CL608e
- Bidirectional Rfid SATO CL612e
- Bidirectional Rfid SATO CT408i
- Bidirectional Rfid SATO CT412i
- Bidirectional Rfid SATO CT424i
- Bidirectional Rfid SATO CW408
- Bidirectional SATO CZ408
- Bidirectional SATO CZ412
- Bidirectional SATO DR308e
- Bidirectional Rfid SATO GL408e
- Bidirectional Rfid SATO GL412e
- Bidirectional Rfid SATO GT408e
- Bidirectional Rfid SATO GT412e
- Bidirectional Rfid SATO GT424e
- Bidirectional Rfid SATO GZ408e
- Bidirectional Rfid SATO GZ412e
- Bidirectional SATO GZ608e
- Bidirectional SATO GZ612e
- Bidirectional SATO HR212
- Bidirectional SATO HR224
- Bidirectional SATO LC408e
- Bidirectional SATO LC412e
- Bidirectional Rfid SATO LM408e
- Bidirectional Rfid SATO LM412e
- Bidirectional SATO Lt408
- Bidirectional Rfid SATO M-10e
- Bidirectional SATO M-5900RVe
- Bidirectional SATO M84 Pro 200DPI
- Bidirectional SATO M84 Pro 300DPI
- Bidirectional SATO M84 Pro 600DPI
- Bidirectional Rfid SATO M-8459Se
- Bidirectional Rfid SATO M-8460Se
- Bidirectional Rfid SATO M-8465Se
- Bidirectional Rfid SATO M-8485Se
- Bidirectional Rfid SATO M-8490Se
- Bidirectional SATO MB200i
- Bidirectional SATO MB201i
- Bidirectional Rfid SATO BF408R
- Bidirectional Rfid SATO BF412R
- Bidirectional Rfid SATO CL4NX 203dpi
- Bidirectional Rfid SATO CL4NX 305dpi
- Bidirectional Rfid SATO CL4NX 609dpi
- Bidirectional Rfid SATO CL4NX-J 203dpi
- Bidirectional Rfid SATO CL4NX-J 305dpi
- Bidirectional Rfid SATO CL4NX-J 609dpi
- Bidirectional SATO CL6NX 203dpi
- Bidirectional SATO CL6NX 305dpi
- Bidirectional SATO CL6NX-J 203dpi
- Bidirectional SATO CL6NX-J 305dpi
- Bidirectional SATO HA212R
- Bidirectional SATO HA224R
- Bidirectional Rfid SATO L'esprit v/ex 408
- Bidirectional Rfid SATO L'esprit v/ex 412
- Bidirectional SATO M-48Pro12
- Bidirectional SATO M-48Pro24
- Bidirectional SATO M-48Pro8
- Bidirectional SATO MB400i
- Bidirectional SATO MB410i
- Bidirectional Rfid SATO S-8408
- Bidirectional Rfid SATO S-8412
- Bidirectional Rfid SATO S-8424
- Bidirectional Rfid SATO S84-ex 203dpi
- Bidirectional Rfid SATO S84-ex 305dpi
- Bidirectional Rfid SATO S84-ex 609dpi
- Bidirectional SATO S86-ex 203dpi
- Bidirectional SATO S86-ex 305dpi
- Bidirectional Rfid SATO SG112T/R
- Bidirectional Rfid SATO SG408R
- Bidirectional Rfid SATO SG408R ex
- Bidirectional Rfid SATO SG412R
- Bidirectional Rfid SATO SG412R ex
- Bidirectional Rfid SATO SG424R
- Bidirectional Rfid SATO SG424R ex
- Bidirectional Rfid SATO SG608R
- Bidirectional Rfid SATO SG612R
- Bidirectional Rfid SATO ST308R
- Bidirectional Rfid SATO ST312R
- Bidirectional Rfid SATO TG308
- Bidirectional Rfid SATO TG312
- Bidirectional SATO WS408
- Bidirectional SATO WS412
|Bidirectional||Le modèle d'imprimante prend en charge la communication bidirectionnelle. Le pilote NiceLabel peut obtenir le retour de l'état de l'imprimante. L'état peut être signalé à et affiché dans NiceLabel.|
|Rfid||Cette imprimante prend en charge la technologie RFID. Vous pouvez programmer les étiquettes RFID intégrées dans l'étiquette intelligente.|
|Dernière version :
Date modifiée :
April 24, 2018
|NiceLabel drivers are tested and work on:||Windows Vista, Windows 7, Windows 8, Windows 8.1, Windows 10, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016|
|Old operating system:||Les pilotes NiceLabel ne sont plus testés sous Windows XP et Windows Server 2003|
Notes de mise à jour
|Release version||Release description|
|Ver.: 188.8.131.5203||Fixed issue with prints remaining in spooler until spooler is restarted or bidirectional support is turned off and on again.|
Driver help file has been updated.
|Ver.: 184.108.40.20639||Maxicode in Mode 3 (alphanumeric postal code) containing characters (not only digits) did not print. This is fixed now.|
|Ver.: 7.8.01.13587||Print Test Page button functionality was improved.|
|Ver.: 7.8.01.13450||Status (monitor) files are upadted for SATO printers.|
|Ver.: 7.8.01.13372||"Test print" button is added to driver's properties dialog. It prints test label to help user adjust printer settings correctly.|
|Ver.: 7.8.01.13372||Bidirectional mode selection (Status4/Status5) has been removed from driver's GUI. Driver automatically detects correct mode.|
|Ver.: 7.8.01.13353||Updated maximum print dimensions for SATO printers.|
|Ver.: 7.5.01.12874||Overlays enabled on SATO NX printers.|
|Ver.: 7.5.00.12826||PJM tag support was added to SATO CL4NX-J printers.|
|Ver.: 220.127.116.1121||GS1Datamatrix and GS1Code128 compatibility was improved for NL65.|
|Ver.: 18.104.22.16814||Fixed max offset for start position on barcode verifier (CLNX models).|
|Ver.: 22.214.171.12400||Correct driver's language is selected in language list prior driver installation.|
|Ver.: 126.96.36.19972||RFID read and print as content of 2D code is working now.|
|Ver.: 188.8.131.5217||Fixed issue with incorrect QR barcode size or errors in stream when printing QR barcode using barcode fonts. Changed QR encoding from UTF8 back to Shift JIS using barcode fonts.|
|Ver.: 184.108.40.20677||Stability and compatibility was improved when using from NiceLabel Automation.|
|Ver.: 220.127.116.1160||Downloading font procedure was improved.|
|Ver.: 18.104.22.16851||Internal flash option is not available for S84ex/S86ex printer when doing store label to printer.|
|Ver.: 22.214.171.12434||Minimum offset (left and top) margins are corrected.|
|Ver.: 126.96.36.19921||Added PJM RFID support for CL4NX models.|
|Ver.: 188.8.131.5209||Maximum dimensions for 2D codes are expanded.|
|Ver.: 7.4.00.12049||Added support for the new SATO LC4e printers.|
|Ver.: 7.4.00.12049||GS1-128 encoding set to mode C when possible.|
|Ver.: 7.4.00.12049||Additional predefined RTC added to SATO printers (hh:mm).|
|Ver.: 7.4.00.11830||Korean language added.|
|Ver.: 184.108.40.20619||Fixed issue with some windows applications showing negative quantity numbers in print dialog.|
|Ver.: 220.127.116.1199||Installation of 32bit driver for sharing printer on 64bit OS has failed. This is corrected now.|
|Ver.: 18.104.22.16883||Implemented "Two color areas" for some SATO printers (CTi).|
|Ver.: 7.3.05.11119||Label size is part of data when storing label template on new NX and S86ex printers.|
|Ver.: 7.3.04.11017||When opening label file created with old printer driver version NiceLabel has crashed. This is corrected now.|
|Ver.: 7.3.03.11030||WS408 and WS412 printer models are supported in SATO NiceLabel driver.|
|Ver.: 7.3.03.10977||When using XML sore/recall Unicode strings are not printed correctly. This is corrected now.|
|Ver.: 7.3.03.10951||Fixed issue with Advanced TCP/IP port incorrectly handling multiple connections to same printer which could result in jobs being stuck in spooler or even data loss.|
|Ver.: 7.3.02.10893||Fixed issue with data being sent to printer when the printer is in error state.|
|Ver.: 7.3.02.10872||Merge from v5 to v7 driver is now working OK also for cutter parameters.|
|Ver.: 7.3.02.10711||Fixed preview for hour in labelling software when using printer clock variable (timezone was not handled correctly).|
|Ver.: 7.3.02.10707||When switching from printer model without media type option to the printer with media type, default driver setting is not used. This is corrected now.|
|Ver.: 7.3.01.10659||Fixed issue with MicroPDF not being printed when version is set to automatic mode.|
|Ver.: 7.3.01.10591||SATO S84ex and S86ex printer models use now "2D" command for all 2D codes.|
|Ver.: 7.3.01.10529||When exporting label using XML export, label name is the same now in export file and recall file.|
|Ver.: 7.3.00.10329||UPC-A, EAN8 and EAN-13 barcodes with human readable were disabled when used with real time clock on S84ex printers.|
|Ver.: 7.0.03.9638||Unit "system default" is no longer available as one of the possible measurement units on driver's GUI. Therefore all labels stored with "system default" unit will be opened with measurement unit set to cm.|
|Ver.: 7.0.03.9636||Port monitor on second print has crashed print spooler when using Advanced TCP/IP. This is fixed now..|
|Ver.: 7.0.03.9626||Some characters (<ETX>, <STX>, ...) were incorrectly encoded in CODE128 barcodes.|
|Ver.: 7.0.03.9620||Added "Command Fonts" option to the driver.|
|Ver.: 7.0.00.9569||Fixed issue with missing first character in text when using X23 and X24 fonts on HR2xx printer models.|
|Ver.: 7.0.00.9559||Fixed issue with unprintable area on labels made by version 5 drivers being positrionned on the wrong side.|
|Ver.: 22.214.171.12488||Fixed issue with high graphics being cut into more then one image. Graphics are now cut only if they are over the size supported by printer.|
|Ver.: 126.96.36.19990||Added new NFC Rfid tags and lock support to Sato printers.|
|Ver.: 188.8.131.5243||TID memory bank is now one of the data fields for EPC (Class 1) Gen2 tag.|
|Ver.: 184.108.40.20630||"Use legacy RFID locking command" option is added to GUI. This is option is available just on SATO CLNX, CLNXJ and S84ex series.|
Concatenate functionality is supported.
|Ver.: 220.127.116.1160||Lock parameter is send with IP0 command also when unlock is selected.|
|Ver.: 18.104.22.16816||Registry setting for close connection type was added.|
|Ver.: 22.214.171.12447||If counter variables are not internal will not be present in recall stream.|
|Ver.: 126.96.36.19934||Corrected label size capability calculation.|
|Ver.: 188.8.131.5228||ČĆŠŽ characters are not printed if used as prefix/suffix.|
|Ver.: 184.108.40.20621||Fixed driver crashes occurring on labels with empty variable elements .|
|Ver.: 220.127.116.1107||Incorrect value is retrieved during recall when there are elements with same variable contents.|
Unicode contents are now correctly handled in bar codes that support multiple code pages.
|Ver.: 18.104.22.16838||Merging settings between printers with different "Use printer default" settings didn`t work.|
|Ver.: 22.214.171.12487||Exporting printer settings as non administrator user doesn`t work.|
|Ver.: 126.96.36.19990||New firmware for SATO CLNX printers will support also new RFID locking command lc2. This option is supported also in the driver.|
|Ver.: 188.8.131.5290||New RFID locking command is supported just on CLNX printers and not also for S84ex.|
|Ver.: 184.108.40.20618||Status monitor error definition files were added to SATO OEM distribution.|
|Ver.: 220.127.116.1137||Fixed store/recall functionality for hardware counters.|
|Ver.: 18.104.22.16828||When using multiple labels in a row the barcode HR is missing on second row of labels. This is fixed now.|
|Ver.: 22.214.171.12419||Doing store/recall the graphics are overwritten every time, because of identical ID. The result is that just last stored layout is working OK. This is fixed now and graphic ID is dependent on format number which value is added to the original graphic ID.|
|Ver.: 126.96.36.19919||Doing store/recall in XML format, always format number 1 is recalled. This is corrected now.|
|Ver.: 188.8.131.5200||Fixed issue with graphics not being printed when using store/recall.|
|Ver.: 184.108.40.20600||Unicode encoding for some internal fonts was changed from UTF-16 to UTF-8.|
|Ver.: 220.127.116.1171||Stripping empty space around graphics elements was improved.|
|Ver.: 18.104.22.16871||Graphics optimization was improved and combined with stripping empty space around graphics.|
|Ver.: 22.214.171.12436||Command for printing UPC-A barcode was updated.|
|Ver.: 126.96.36.19971||Drivers about dialog use different web link for SATO International and Japan distribution.|
|Ver.: 188.8.131.5297||Cut every label functionality is now working as expected when using Crystal Report application.|
Fixed wrong syntax on MBi printers when using Configure Printer option.
Fixed missing byte in command syntax on CTi printer when using Configure Printer option.
"Auto power off [ms]" corrected to "Auto power off [min]".
Maximum label width for MB400i fixed to 832 dots.
Maximum label width for MB410i fixed to 1248 dots.
Minimum "Pitch offset" and "Dispense offset" are set to -40.
Removed "Dispenser" option from "Print operation mode".
Auto power off is not read from printer (printer language limitation).
|Ver.: 184.108.40.20694||Code93 is working now also when doing store/recall printing type.|
No error when encoding RFID with locking enabled on some printers that do not support locking.
|Ver.: 220.127.116.1177||UPC-A barcode prints correcty on all CL4NX-J and CL6NX-J models.|
|Ver.: 18.104.22.16869||Datamatrix barcode print stream was corrected.|
|Ver.: 22.214.171.12433||Added 'Please restart the printer after sending settings' warning message in RFID option dialog.|
|Ver.: 126.96.36.19917||S84/86ex printers have selected option "Let printer control this option" for Media type and Operation mode options.|
|Ver.: 188.8.131.5237||SatoJpnNG and SatoPW distributions are merged into SatoJpnNG2.|
XML export (to internal memory and to memory cartridge) was not working correctly.
|Ver.: 184.108.40.2068||Menu with options "Send this parameter to printer" and "Let printer control this option" is no longer displayed on "Configure Printer" dialog box.|
|Ver.: 220.127.116.1146||Added HF RFID tags support to CL4NX printer.|
|Ver.: 18.104.22.16826||SATO printers with PJM stacked RFID tags (CG2xx, CL408e, CL412e, GZ408e, GZ412e) support now also RFID setting dialog for RFID module.|
|Ver.: 22.214.171.12407||Solved problems with input long description of font in Driver Properties/Fonts.|
|Ver.: 126.96.36.19992||Paper ID overlapping when delete and restore pre-define paper.|
|Ver.: 188.8.131.5278||CL4NX-J's default label size is displayed for PW208 printer driver|
|Ver.: 184.108.40.20678||Stocks with to large page sizes were available to select on PW models.|
Character width table for font "SATO Gothic Japanese" is corrected.
|Ver.: 220.127.116.1174||Export to printer option corrected in a way <ESC>/Y command is sent just with XML export variant.|
S84ex/S86ex can store label layout into three different memory locations:
CC0: Internal flash (Printer)
CC1: Memory cartridge (FROM)
CC2: SD Card (or USB memory)
|Ver.: 18.104.22.16865||SATO S84ex/S86ex models needs to send ESC+PO1 command for backfeed offset when using linerless operation mode ESC+PM5 (and not PO0 like on all other SATO models).|
|Ver.: 22.214.171.12462||SATO S84ex/S86ex models have just three media type options: Continuous, Labels with Gap and Labels with black mark.|
|Ver.: 126.96.36.19959||SATO CL4NX-J and SATO CL6NX-J printer models use <~B> cutter command for cut at the end of job.|
|Ver.: 188.8.131.5255||Fixed issue with batch cut commands appearing after each page in job if not using NiceLabel.|
|Ver.: 184.108.40.20645||Import/export function in driver settings now correctly handles "Let printer control this option/Send this parameter to printer".|
NiceLabel driver support also Japanese version of SATO CL-NX printer models:
SATO CL4NX-J 203dpi
SATO CL4NX-J 305dpi
SATO CL4NX-J 609dpi
SATO CL6NX-J 203dpi
SATO CL6NX-J 305dpi
|Ver.: 220.127.116.1143||SATO M84 Pro 600DPI printer does not support EX0 command.|
|Ver.: 18.104.22.16827||Improved presentation of X2 fonts on screen.|
|Ver.: 22.214.171.12420||Improved appearance of bitmap fonts (sizes 16, 22, 24, 32,and 40) on screen to better represent printed results.|
|Ver.: 126.96.36.19904||RSS and RSS expanded stacked barcode fonts with maximum height are now printed correctly.|
|Ver.: 188.8.131.5209||If user select reset on Maintenance dialog, all items are reset now. This includes also selection for "Send this parameter to printer".|
|Ver.: 184.108.40.20625||Fixed unicode text is not exported as unicode when doing Export to SAP or Custom Export in NiceLabel.|
|Ver.: 220.127.116.1118||Updated Japanese translations in driver and PrnInst application.|
|Ver.: 18.104.22.16882||Fixed cutter usage with different scenarios (advanced cutter, batch cut,...).|
|Ver.: 22.214.171.12457||UPCE barcode font did not print when 7 digits (6 digits data + check digit) were entered. This is fixed now.|
|Ver.: 126.96.36.19956||Fixed Enable/Disable toggle for Print Mode (Cutter) GUI dialog.|
|Ver.: 188.8.131.5251||Support for old USB port type was removed from Port monitor.|
|Ver.: 184.108.40.20650||Barcode font description is limited to max. 255 characters.|
|Ver.: 220.127.116.1145||Incorrect Japanese translations in PrnInst corrected.|
|Ver.: 18.104.22.16841||Attempted creation of a port with a name that is already used will no longer make user interface unusable.|
FNC1 in Datamatrix barcode is supported.
|Ver.: 22.214.171.12419||Bar code fonts for Japanese models are encoded in Shift JIS.|
|Ver.: 126.96.36.19909||From NX printers and later also international models are using new 2D code syntax.|
|Ver.: 188.8.131.5206||After installation stocks are preloaded.|
|Ver.: 184.108.40.20686||Type column on for font substitution, command font and barcode font is now translated.|
|Ver.: 220.127.116.1166||When Reseting settings to default values, "Apply" button will be enabled.|
|Ver.: 18.104.22.16814||Border sizes can no longer be changed as those settings are not supported on printer.|
|Ver.: 22.214.171.12474||Tear-off delay on Configure printer dialog for CLNX printers accept values 0, 5-200 ms.|
|Ver.: 126.96.36.19972||Port monitor now correctly shows all serial (COM) and parallel (LPT) ports on the computer.|
|Ver.: 188.8.131.5241||Updated fonts substitution dialog.|
|Ver.: 184.108.40.20630||Command fonts are encoded in Shift JIS.|
|Ver.: 220.127.116.1146||PrnInst information (installed languages) missing in inf file.|
|Ver.: 18.104.22.16801||V6 driver now shows also DPI when running VB script for printer info.|
|Ver.: 22.214.171.12491||PrnInst application removes only NiceLabel Drivers driver packages from Driver Store.|
|Ver.: 126.96.36.19985||When setting out-of-scope values at silent installation, an error is not generated, but it is displayed as blank.|
|Ver.: 188.8.131.5266||Error is reported when using function "Export to SAP" on SATO CG printers.|
|Ver.: 184.108.40.20600||Can not convert QR code to 2byte code under "word".|
|Ver.: 220.127.116.1190||EAN-13 barcode is printed correctly even if it starts with the leading zeros.|
|Ver.: 18.104.22.16831||Clear format command is sent also when export to printer in XML format.|
NiceLabel driver support also following new SATO models:
SATO CL6NX 203dpi
SATO CL6NX 305dpi
|Ver.: 22.214.171.12477||Using "Store to printer" functionality generates wrong stream if default variable value is empty.|
NiceLabel driver support also following SATO printer models:
SATO S84-ex 203dpi
SATO S84-ex 305dpi
SATO S84-ex 609dpi
SATO S86-ex 203dpi
SATO S86-ex 305dpi
|Ver.: 126.96.36.19983||Added X20, X21, X22, X23 and X24 fonts.|
|Ver.: 188.8.131.5242||Fixed issue with Line Substitution being enabled by default (should be disabled)|
|Ver.: 184.108.40.20630||Command ESC+AR is not sent to the printer anymore. This command has enabled standard print area but now A1 command replace it. Printers will use now expanded print area which enables longer print size.|
Implemented different width table for SATO CG Sleek and CG Stream fonts. This improves WYSIWYG representation in labeling applications.
|Ver.: 220.127.116.1118||Limited barcode darkness and darkness range selection to valid combinations.|
|Ver.: 18.104.22.16815||When user selects Linerless operation mode driver needs to send <PMC and <PO2> instead of <PM>5 and <PO>0 like on other SATO models. This is true now.|
|Ver.: 22.214.171.12408||Japanese language was updated.|
|Ver.: 126.96.36.19988||Advanced settings section was removed from UI on PW208 printer.|
|Ver.: 188.8.131.5287||Minimum limits for Pitch offset, Tear-off offset and Dispense offset corrected on PW208 printer.|
|Ver.: 184.108.40.20684||After adding port from Printer Install Wizard Network Discovery, timeout values are correct.|
|Ver.: 220.127.116.1172||Some PG commands are wrong.|
|Ver.: 18.104.22.16865||does not enter sleep mode due to sending ENQ continuously with working the system of Label Services.|
|Ver.: 22.214.171.12448||Parameter cd of <#F>abcd can not be specified.D|
|Ver.: 126.96.36.19946||Problem is the output value of "<PO>" command.|
When reading PG command from printer, correct user message is displayed in case of unsuccessful read.
|Ver.: 188.8.131.5231||Maximum speed setting on Configure printer and Print Options dialogs is limited now on CL4NX and PW208 printers. This limitation is enforced only for specific operation mode settings.|
|Ver.: 184.108.40.20626||Error messages on "Configure Printer" tab are not translated.|
|Ver.: 220.127.116.1125||Added No backfeed option to Dispenser mode on PW printer models|
|Ver.: 18.104.22.16823||Uninstall button is enabled if there exist some printers to uninstall.|
|Ver.: 22.214.171.12423||Only drivers developed by Europlus can be uninstalled|
|Ver.: 126.96.36.19918||GS1 DataBar UPC-E barcode font can now accept UPC-A encoding.|
|Ver.: 188.8.131.5216||"Barcode darkness range" and "Barcode darkness" under driver setting/printer setting/ barcode was not translated into Japanese language. These strings are updated now.|
|Ver.: 184.108.40.20615||SATO PW208m printer is supported. The only difference to PW208 is Wi-Fi support.|
|Ver.: 220.127.116.1114||"Configure Printer" screen in "Driver settings" moves up and down when using Up/Down controls on edit windows.|
|Ver.: 18.104.22.16813||SATO PW printer does not support Status 5. It is using just Status 4 and because of this selection is removed from GUI (Printing Preferences > Print Options > Advanced settings).|
The input value range for Tear off delay on Configure printer dialog should be from 0 to 200. By default it is 0. This is corrected now for SATO NX and PW models. Before the correction the range was 5-200 and default 10.
Barcode fonts for SATO PW208 did not have the same description as other SATO Japanese models.
- barcode font "SSCC182 should use name "GS1 128 (SSCC-18)"
- bookland barcode font should use name "UPC add-on"
- Datamatrix barcode should not support ECC and formatID options
This is corrected now.
After driver installation the default driver language was set into English.It should be in Japanese. This is corrected now.
There are also just two languages supported (Japanese and English) like for all other Japanese models.
|Ver.: 22.214.171.12409||SATO PW printer did not print PDF417, because the driver was sending the "<BK> command" but it must send the "<2D10> command". This is corrected now.|
SATO PW printer did not print MaxiCode, because the driver was sending the "<BV> command" but it must send the "<2D20> command". This is corrected now.
|Ver.: 126.96.36.19909||SATO PW208 should support darkness range from A to F according to the specification, but only A has been available before this correction.|
|Ver.: 188.8.131.5295||"Export to Printer" functionality on SATO PW printer is disabled.|
|Ver.: 184.108.40.20668||Backfeed is disabled only for printers which have just one Backfeed option.|
Darkness range for CL4NX printers is A-F (not just A).
Kanji code on "Configure printer" dialog needs to have 6 values (JIS code, Shift JIS code, Unicode UTF16, GB18030, BIG5, KCS5601) and not just 2.
CUT_OFFSET - both minimum and maximum values are corrected (+/- 99 dots)
DISP_OFFSET - both minimum and maximum values are incorrect (+/- 99 dots)
PROPORTIONAL - driver now send correctly "1" for proportional, and "0" for fixed character spacing (before the correction "0" in both cases).
|Ver.: 220.127.116.1114||In come cases of EPC (Class 1) Gen2 and use of EPC encoding, there ware duplicate EPC fields in print stream. This is corrected now.|
Media type (ESC+IG), Printing mode (ESC+PH) and Operation mode with backfeed (ESC+PM, ESC+PO) are added into CL4NX and CL6NX.
Corrections after 18.104.22.16825 Beta version:
CL4NX Operation mode - Linerless - Backfeed mode is "Before printing" instead of "No backfeed"
CL4NX Operation mode - Linerless - "After printng" is removed
CL4NX Operation mode - Linerless - Operation mode "Linerless" has just one value on NX4 printer: "Before printing". "No backfeed" option has been removed. Print stream reflect with sending PM5 and not PM6.
CL4NX/CL6NX Operation Mode - Partial cut - cut when printing - Backfeed mode is "Before printing" instead of After printing
CL6NX Operation mode - Partial cut - cut when printing - "Before printing" option has been removed
CL6NX Operation mode - Partial cut - cut when printing - print stream reflect PM9. This is solved with change of operation mode option from Partial cut into "Cutter - cut when printing). This option sends PMB.
Operation mode "Cutter - cut when printing" has just one Backfeed mode "Before printing". Because no other is possible, the combo for backfeed is disabled disabled on GUI.
Media type (ESC+IG):
Media type combo for CG2 printers is extended with "Wristband without carrier" (SBPL manual:"Transmissive 2 - for wrist bands").
Also GZ6 printers support Media type option now.
Operation mode (ESC+PM, ESC+PO):
All printer models with Operation mode option, support Backfeed offset and Pitch offset.
Operation mode "Linerless" is removed for CG2 printers.
HR printer models also support Operation mode and Backfeed options.
MB2i and MB4i printer also support Operation mode with two options (Continuous, Tear off).
Print mode (ESC+PH):
GZ, S84ex,S86ex and SG6xxR printer models have now Print mode option on the GUI (Direct thermal/Thermal transfer).
CW printer does not support print mode option (no ribbon core).
Media form (ESC+YE):
Lesprit printer models support now Media form option.
Media form (roll/fanfold) is not supported on HA, HR printers.
Media form (roll/fanfold) is now supported on Lesprit printers.
Darkness range is controlled with printer by default, like it is implemented on the International printer models.
CG4xx and M-10e have darkness range A,B
CZ4xx have darkness range A,B,C,D,E,F
MB printers does not support Overlay function (also GUI option is removed for enable Overlay)
Japanese BF,HA, Lesprit printers does not support Overlay function (also GUI option is removed for enable Overlay).
Added Operation mode for:BF400R, M-48 Pro and ST300R printers. Also Pitch offset is added like it is used on other Japanese printer models.
Added Operation mode > Cutter- cut when prinitng (<ESC+PM>B) for SG600R printers.
Operation mode "Cutter-cut when prinitng" is also added for Store settings dialog (ESC+PG command) on SG600R printers.
When for Operating mode "Dispenser" is selected there are just two Backfeed mode options (No backfeed option has been removed).
There is no Backfeed mode option when "Cutter - cut when printing" is selected for Operation mode.
Operation mode combo has the same width as Backfeed mode to fit the length of all values.
Linerless operation mode sends two PO commands now. PO0 + PO3.
ForBF400R, M-48 Pro and ST300R printers: Operation offset combo is removed from "Print Options" dialog because now the operation mode is supported on all models, and Backfeed offset is used for the operation offset.
All controls on Store Settings dialog used unique command and not the same one as they are in the driver.
|Ver.: 22.214.171.12413||ESC+CC command is not send anymore on MB printers.|
|Ver.: 126.96.36.19992||When the user opens a settings page with scroller, the behaviour of scroller is updated to update the screen smoothly.|
|Ver.: 188.8.131.5277||When exporting a label with variable text to SAP, there was an error (data includes unprintable characters). This is corrected now.|
|Ver.: 184.108.40.20655||Fixed incorrect SGTIN-96 EPC encoding|
Driver crash when store label with RFID and variable connected to RFID data (upc, userdata).
Also store and recall stream is corrected to use multiple variables on RFID.
|Ver.: 220.127.116.1171||SATO CW408 printer does not support CG Times and CG Triumvirate fonts.|
|Ver.: 6.0.09.6525||SATO CW408 support darkness value 1-10 and darkness range A,B.|
|Ver.: 6.0.09.6497||Fixed bug when recalling label with variable GS-1 barcode.|
|Ver.: 6.0.09.6452||SATO MB2xxi printers do not support "Journal mode 2" as an Print mode option on Configure printer dialog. This option is supported just on MB4xxi series.|
|Ver.: 6.0.09.6429||Support selection to enable/disable Overlay function in all models|
|Ver.: 6.0.09.6426||Added RFID support to S84-ex printers|
|Ver.: 6.0.09.6423||CL4NX uses wrong font for human interpretation|
|Ver.: 6.0.09.6421||Empty graphics should not be send to the printer.|
Changed command for printing fonts CG Sleek and CG Stream.
Removed obsolete RFID tag on CL4NX printer
CL4NX printer uses only Free Mapping command for EPC Gen 2 encodings
Printer driver has field Number of copies which works when printing from third party applications that do not support number of copies.
|Ver.: 6.0.09.6349||Sato CL6NX 203dpi and Sato CL6NX 305dpi added.|
|Ver.: 6.0.08.6369||Coordinate of fixed barcode is changed on second page|
|Ver.: 6.0.08.6360||Unprintable area is now correctly displayed on all orientations (rotated portrait or landscape).|
|Ver.: 6.0.08.6350||Order of RFID and Overlay commands corrected|
|Ver.: 6.0.08.6335||When using Store/Recall there was stream syntax error, because variable field ID starts with 00. Correct ID number for variable is 01..99. This is corrected now.|
|Ver.: 6.0.08.6211||Character spacing is not supported on some fonts.|
Some internal fonts on SATO CL4NX can be increased in size beyond limit.
|Ver.: 6.0.08.6191||Vertical positioning of RH fonts (0, Mincho, Alpha, Beta, Folio, Futura, Gamma, OCR-B TrueType, Sans, Serif, Vica, Sleek and Stream) corrected.|
S84 and S86 printer models
Changed "SATO Korean 16" to "SATO 16x16 KSX1001"
Changed "SATO Korean 24" to "SATO 24x24 KSX1001"
Added "SATO 16x16 GB18030"
Added "SATO 24x24 GB18030"
Added "SATO 24x24 BIG5"
|Ver.: 6.0.08.6186||Removed Eas, Power attenuation, Tag offset and RFID Read Protection funcitonality from CL4NX series.|
|Ver.: 6.0.08.6181||Power setting for PJM StackTag (PJM Integrated) RFID tag is now set to 1/4.|
|Ver.: 6.0.08.6179||Fixed error when encoding RFID EPC field (SGTIN96 format) from database.|
|Ver.: 6.0.08.6171||Maximum element dimensions for Line, Rectangle, Text and "fixed document length" corrected.|
CL4NX bitmap font dimensions on screen are corrected.
|Ver.: 6.0.08.6161||SATO GZ4 printer: WYSIWYG for Vica fonts has been imporved again (for example WWWW characters has overlap each other before).|
Fonts with ESC+RH command supported on SATO CL4NX printers
|Ver.: 6.0.08.6150||Support UNICODE in BMP font (XU, XS, XM, XL, U, S, M, WB, WL, $)|
|Ver.: 6.0.08.6150||Added support for BMP Japanese (Mincho and Gothic style), Chinese (Traditional and simplified) and Korean fonts.|
Mobile fonts supported on SATO CL4NX.
|Ver.: 6.0.08.6150||Vector font dimensions for SATO printers corrected.|
|Ver.: 6.0.08.6148||Added vector font to S84-ex/S86-ex models.|
CL4NX SATO GAMMA VICA font name is wrong. The correct name doesn't have RH.
|Ver.: 6.0.08.6142||Optimized slow printing on MBxxxi series.|
Partly corrected name of Japanese fonts (number 2008 changed to 208).
|Ver.: 6.0.08.6138||WYSIWYG for SATO GZ4 printing Gamma and Vica fonts variants has been updated.|
|Ver.: 6.0.08.6128||Maximum media width/height corrected for some SATO models.|
|Ver.: 6.0.08.6120||Printing delay default set to 200ms instead of 50|
|Ver.: 6.0.08.6115||If barcode height is larger than 999 dots in labeling software, then driver send just 999 dots to the printer. In this case there is no error in print stream.|
|Ver.: 6.0.08.6106||Check box "Set fixed document length for continuous label" does not generate illegal SBPL command anymore.|
|Ver.: 6.0.08.6104||The 'Mask' option for QR barcode is removed from dialog.|
|Ver.: 6.0.08.6091||Serial Reference/Number parameter for RFID Gen2 512bit tag is corrected.|
|Ver.: 6.0.08.6089||M-5900RVe printer model should have a standard status 4 bidi enabled (same as CL4xxe models).|
|Ver.: 6.0.08.6082||Backfeed mode commands have corrected (switched) for both option: before printing and after printing.|
|Ver.: 6.0.08.6071||Default media size is 10 cm x 7 cm (width x height).|
|Ver.: 6.0.08.5408||SATO HA and SATO HR printer models support just thermal transfer printing mode. Because of this fact combo box with just one selection is removed from the GUI.|
|>> See more release notes|